How to do the problem of autumn furniture, how to do six tricks to eliminate troubles
NO.1: Increase the gap in the floor
Cause Analysis
After the fall, the weather becomes dry, the humidity in the air is greatly reduced, and the solid wood floor will shrink, resulting in a large gap in the floor. There is some truth to the practice of delaying the maintenance of the company in the spring of the year. In the winter, the shrinkage of solid wood flooring is likely to increase.
Solution
Autumn rework should be careful not to worry, wait until the spring of the next year, after four seasons of warm and cold temperature changes significantly, solid wood floor cracking and deformation problems are no longer developed, and then a one-time repair. This will ensure better results and eliminate the hassle of repeated repairs.
special reminder:
Autumn is coming, solid wood floor waxing maintenance is at the time. Wipe the floor clean before waxing, then apply a layer of floor wax evenly on the surface. After a while, wipe it with a soft cloth until it is smooth and bright. Ventilation should be done as much as possible to keep the air flowing inside the house. After a while, after the weather is getting dry, you need to use a humidifier to adjust the indoor humidity.
NO.2: tarnished solid wood Furniture
Cause Analysis
The surface of solid wood furniture is painted with paint, which is especially important for the maintenance and maintenance of the paint film. Once the paint film is destroyed, it not only affects the appearance of the surface, but also further affects the internal structure of the product. Poor maintenance in autumn can lead to tarnishing or cracking of solid wood furniture.
Solution
Always keep the solid wood furniture clean. Use a soft, dry, soft cloth to wipe off the surface dust every day. Wipe it with a damp cloth for two or three days. If there are stains on the surface of solid wood furniture, do not rub it hard. Use warm tea to remove the stains gently.
special reminder:
In fact, it is advisable to use thin glue to separate the solid wood furniture from the ground, and at the same time let the wall of the solid wood furniture maintain a gap of 0.5-1 cm from the wall. Avoid too humid environments to avoid rotting solid wood furniture.
NO.3: The door frame is cracked.
Cause Analysis
Unless it is a good quality and very thick wood line, it is not solid to install the door cover directly with thinner wood lines. The reason is that the physical properties of the material are different, and such a door cover is not easy to be in stable contact with the wall surface. In addition, the wood line with insufficient thickness will crack and deform when it comes into contact with the wall.
Solution
The door cover crack can be filled with an adhesive and then repaired with the original color paint of the door cover. If the door cover material is too thin, it is best to ask the worker to rework.
special reminder:
Autumn is coming, solid wood floor waxing maintenance is at the time. Wipe the floor clean before waxing, then apply a layer of floor wax evenly on the surface. After a while, wipe it with a soft cloth until it is smooth and bright. Ventilation should be done as much as possible to keep the air flowing inside the house.
NO.4: Seamless tile breaks off
Cause Analysis
Since the thermal expansion and contraction coefficients of the base layer, the bonding layer and the tile itself are very different, under the thermal and cold tension failure of 1 to 2 years, the over-tight coating tends to cause problems such as bulging and breaking of the tile. If you re-mass a large-scale paving after such problems, the cost will be two or three times more expensive than the first time.
Solution
Remove the sand from the back of the tile and mix it with cement and glue. It should be noted that if the tile is only partially peeled off, it is not possible to tap the mortar on the base layer to prevent the original tile from being loose.
Special reminder :
The seam can be adjusted between 2 and 3 mm. At the same time, in order to avoid wasting materials, a number of selected products can be randomly sampled on the ground for non-bonded test shops. If there are obvious chromatic aberrations, dimensional deviations, etc., if the satisfactory results are not achieved after the adjustment of the brick position, the laying should be stopped in time and contact with the material supplier for exchange.
NO.5: The corner of the wallpaper is tilted
Cause Analysis
In the autumn decoration, not only the wallpaper should be “hydratedâ€, but also the wallpaper should be dried naturally, but not in the summer. Because it is so easy to let the freshly laid wallpaper be blown dry by the wind, thus losing water and deformation.
Solution
Clean the original glue on the wallpaper, brush some white latex on the back of the wallpaper, brush the water on the front of the wallpaper, and scrape it with a plastic scraper. Finally, the bead is attached, and the bead is removed after the drying. Because the autumn climate is relatively dry, the wallpaper and wall coverings must be soaked in the water before the paving, and then the glue is applied.
special reminder:
If you encounter wallpaper blistering, first use the sewing needle at home to smear the bubbles on the surface of the wallpaper, release the gas, then use the needle to draw the appropriate amount of adhesive, inject into the needle that has just been punctured, and finally scrape with a squeegee. Compact and dry.
NO.6: Danger of explosion in shower room
Cause Analysis
The interior of the glass shower room is a closed space. When the high temperature and high pressure accumulate to a certain extent, pressure will be formed on the glass, resulting in uneven heating of the glass and explosion.
Solution
The glass is coated with a high-quality transparent safety explosion-proof membrane, which can increase the strength of the glass by more than 6 times. Even if it bursts, the self-explosive glass fragments can be adhered together by the adhesive force of the explosion-proof membrane to prevent the glass from being caused by the glass explosion. The debris splashed and wounded.
special reminder:
Although the strength of tempered glass is relatively high, the characteristic of tempered glass is that it is more afraid of sharp things than ordinary glass. The fixed shower room and the positive end of the wall will affect the safety of tempered glass. If it is collided again, it will easily cause the whole. explosion.
Sausage Stuffer:
Stainless Steel Home Sausage Stuffers are made up of stainless steel grade of 201, 304 and cast aluminum. Not afraid of food safety and easy for cleaning, suitable for home using. These manual sausage stuffers have 4 filling tubes with different diameters for different requirements, customers could choose as their own needs. The installation of manual sausage stuffers is not complex, customers could do by self, we will provide detailed installation manual.
Sausage Filler,Food Machinery,Beverage Machinery,Stainless Steel Stuffer Filler Machine
Suzhou CoreMission International Trading Co.,Ltd. , https://www.szcoremission.com