SAM 935TM
Monitoring and measuring system
manual
Berkeley Nuclear Subsidiary
3060 Kerner Boulevard # 2
San Rafael, CA 94901 USA
800-234-7858
415-453-9955
fax
Http:
Beijing Oriental Yuantong Technology Development Co., Ltd.
Address: Building 24, Xihuan Road, Changping District, Beijing
Phone: 010-69728262, 69722157, 69722398, 13911151403
E-mail:
http: //
Beijing Oriental Yuantong Technology Development Co., Ltd. solemnly declares:
If there is any discrepancy between the Chinese translation and the original English text, the original English text shall prevail.
Firmware version 02.10.00
U.S. Patent Number: 5608222
1995-1999, all versions
Printed in the USA
Warranty
The Berkeley Nuclear Subsidiary guarantees all instruments (including components) under normal use, free of charge regardless of material or process, and the service period is one year. If repairs are required during the warranty period, please contact the factory for component replacement and shipping instructions. The warranty instrument needs to provide the instrument number. If the instrument has been repaired and modified by a non-Berkeley nuclear subsidiary authorized department, the warranty period will expire.
Important notice !! Please read carefully
Copyright notice
The firmware in this instrument is protected by copyright laws and international treaties, and you must treat the firmware like any other copyrighted item. The copyright law strictly prohibits making copies of the firmware for any reason, and you may not copy the written materials attached to this product.
SAM 935TM
Monitoring system user manual (translation)
table of Contents
1 Introduction ............................................................... 7
1. 1 How to use this manual ............................................................... 7.
2 Quick access guide ............................................. 9
2.1 Turn on SAM935 ........................................................................ 9
2.1.1 Quick calibration and background reading ............................................... 10
2.1.2 Reading .............................................................................. 13
2.2 Alarm check .............................................................................. 15
2. 3Shutdown .............................................................................. 16
3 Hardware connection ......................................................... 17
3.1 Battery charging and power connection ......................................................... 17
3.2 Connect the printer ........................................................................... 18
3.3 Connect remote computers .................................................................. 19
3. 4 Connect the external detector (optional) ……………………………… 20
4 SAM935 user interface ……………………………… ..21
4.1 Front panel .................................................................................... 21
4.2 Scrolling the menu .............................................................................. 22
4. 3 Editing Guidelines ........................................................................ 22
5 SAM935 configuration selection ……………………………… .. 25
5.1 Start SAM935 .............................................................................. 25
5.2 Scale SAM935 again .................................................................. 28
5.2.1 Use the Eu-152 source to run the second energy scale below 2meV ........................ 29
5.2.2 The operating energy range is extended to the square energy scale below 3meV .................. 33
5.2.3 Re-store the scale factor after the firmware is reset ....................................... 37
5.2.4 Dose rate scale ............................................................ 38
5.2.5 Add new scale label ............................................................ 42
5. 3 Configure the dose rate unit and trigger ......................................................... 42
6 SAM935 operation mode .......................................... 45
6.1 Monitoring operation mode ........................................................................ 46
6.2 Monitoring operation mode ........................................................................ 48
6.3 Detailed operation mode ..................................................................... 49
6.4 Manual operation mode .............................................................................. 51
6.4.1 Pre-set by MCA .................................................................. 54
6.4.2 Manual hardware adjustment ......................................................... 55
Click to enter the booth of Beijing Oriental Yuantong Technology Development Co., Ltd.
Sweep, welcome attention
Official WeChat of Educational Equipment Procurement Network
Master the latest and most authoritative information in the education equipment industry
Copyright and Disclaimer:
â‘ The copyright of all works on this website that indicate "Source: China Education Equipment Purchasing Network" belongs to China Education Equipment Purchasing Network, and may not be reproduced, edited or used in other ways without authorization from this website. Works that have been authorized by this website should be used within the scope of authorization, and indicate "Source: China Education Equipment Purchase Network". Violators of this website will be held accountable for legal liabilities.
â‘¡ All works on this website that indicate "Source: XXX (non-this website)" are reproduced from other media. The purpose of this reprint is to transmit more information. This does not mean that this website agrees with its views and is responsible for its authenticity. Take direct responsibility and joint liability for infringement of such works. If other media, websites or individuals download and use it from this website, they must keep the "source of the manuscript" indicated on this website, and bear the legal responsibility of copyright and other.
â‘¢ If the content of the work, copyright and other issues are involved, please contact this website within two weeks from the date of publication of the work, otherwise it is deemed to waive the relevant rights.
ESONE New Materials Co.,Ltd has developed a full range of open mesh belting
products, mesh size ranging from 1x1mm, 2x2mm, 2x2.5mm, 4x4mm, 6x6mm, 8x8mm to 10x10mm.
And ESONE open mesh belt is using fiberglass, Kevlar or Nomex as basic material, offering PTFE belt with high mechanical strength in order to meet the high request.
Our open mesh Belts are widely used
for flooring, drying, screen printing, non woven fabric, food processing, heat sealing packing, glass manufacturing, wood processing industry, which can provide a high percentage of open
surface area, creating maximum airflow and sufficient operation with minimum
heat loss. Width and length stability of the belts are retain over full range
of operating temperature.
PTFE Mesh Conveyor Belts
PTFE Mesh Conveyor Belt, Teflon Belt, PTFE Conveyor Belt, Teflon Mesh Belt
Jiangsu Esone New Material Co,.Ltd , https://www.cookware-manufacturer.com
